kernel/drivers/extcon/extcon-max8997.c, branch linux-5.1.y

extcon: max8997: Fix lack of path setting in USB device mode

2018-11-14T00:06:32Z

MAX8997 driver disables automatic path selection from MicroUSB connector and manually sets path to either UART or USB lines. However the code for setting USB path worked only for USB host mode (when ID pin is set to ground). When standard USB cable (USB device mode) is connected, path registers are not touched. This means that once the non-USB accessory is connected to MAX8997-operated micro USB port, the path is no longer set to USB and USB device mode doesn't work. This patch fixes it by setting USB path both for USB and USB host modes. Signed-off-by: Marek Szyprowski Signed-off-by: Chanwoo Choi

extcon: max8997: Avoid forcing UART path on drive probe

2018-11-12T00:17:13Z

Driver unconditionally forces UART path during probe, probably to ensure that one can get kernel serial log as soon as possible. This approach causes some issues, especially when board is booted with non-UART cable connected to micro-USB port. For example, when USB cable is connected, UART TX/RX lines are unconditionally short-circuited to USB D+/D- lines. This is in turn recognized by a series of serial BREAK signals and some random characters when USB host tries to perform enumeration procedure. To solve the above issue and keep UART console operational as early as possible, set UART path only when USB ID reports UART capable cable. Signed-off-by: Marek Szyprowski Signed-off-by: Chanwoo Choi

extcon: maxim: Add SPDX license identifiers

2018-08-28T02:13:20Z

Replace GPL v2.0+ license statements with SPDX license identifiers. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Chanwoo Choi

extcon: max8997: Delete unneeded initialization in max8997_muic_set_path()

2017-11-27T01:23:47Z

The variable "ret" will be set to an appropriate value a bit later. Thus this patch omits the explicit initialization at the beginning. Signed-off-by: Markus Elfring Signed-off-by: Chanwoo Choi

extcon: Split out extcon header file for consumer and provider device

2017-10-23T05:07:58Z

The extcon has two type of extcon devices as following. - 'extcon provider deivce' adds new extcon device and detect the state/properties of external connector. Also, it notifies the state/properties to the extcon consumer device. - 'extcon consumer device' gets the change state/properties from extcon provider device. Prior to that, include/linux/extcon.h contains all exported API for both provider and consumer device driver. To clarify the meaning of header file and to remove the wrong use-case on consumer device, this patch separates into extcon.h and extcon-provider.h. [Description for include/linux/{extcon.h|extcon-provider.h}] - extcon.h includes the extcon API and data structure for extcon consumer device driver. This header file contains the following APIs: : Register/unregister the notifier to catch the change of extcon device : Get the extcon device instance : Get the extcon device name : Get the state of each external connector : Get the property value of each external connector : Get the property capability of each external connector - extcon-provider.h includes the extcon API and data structure for extcon provider device driver. This header file contains the following APIs: : Include 'include/linux/extcon.h' : Allocate the memory for extcon device instance : Register/unregister extcon device : Set the state of each external connector : Set the property value of each external connector : Set the property capability of each external connector Signed-off-by: Chanwoo Choi Acked-by: Sebastian Reichel Acked-by: Chen-Yu Tsai Acked-by: Charles Keepax Acked-by: Lee Jones Acked-by: Felipe Balbi Acked-by: Yoshihiro Shimoda Acked-by: Kishon Vijay Abraham I

extcon: Use the extcon_set_state_sync() instead of deprecated functions

2016-09-13T02:26:26Z

This patch alters the renamed extcon API to set the state of the external connectors instead of deprecated extcon_set_cable_state_(). Because the patch[1] modifies the function name to maintain the function naming pattern. - extcon_set_cable_state_() -> extcon_set_state_sync() - extcon_get_cable_state_() -> extcon_get_state() [1] https://lkml.org/lkml/2016/8/4/729 - extcon: Rename the extcon_set/get_state() to maintain the function naming pattern Signed-off-by: Chanwoo Choi Acked-by: Charles Keepax Acked-by: Roger Quadros

extcon: Add the EXTCON_CHG_USB_SDP to support SDP charing port

2016-01-25T04:16:53Z

This patch adds the new EXTCON_CHG_USB_SDP connector to support SDP (Standard Downstream Port) USB charging port. The commit 11eecf910bd8 ("extcon: Modify the id and name of external connector") add the new EXTCON_CHG_USB_SDP connector which support the both data transfer and usb charging at the same time. Signed-off-by: Chanwoo Choi Reviewed-by: Krzysztof Kozlowski

extcon: Modify the id and name of external connector

2015-10-15T23:30:09Z

This patch modifies the id and name of external connector with the additional prefix to clarify both attribute and meaning of external connector as following: - EXTCON_CHG_* mean the charger connector. - EXTCON_JACK_* mean the jack connector. - EXTCON_DISP_* mean the display port connector. Following table show the new name of external connector with old name: -------------------------------------------------- Old extcon name | New extcon name | -------------------------------------------------- EXTCON_TA | EXTCON_CHG_USB_DCP | EXTCON_CHARGE_DOWNSTREAM| EXTCON_CHG_USB_CDP | EXTCON_FAST_CHARGER | EXTCON_CHG_USB_FAST | EXTCON_SLOW_CHARGER | EXTCON_CHG_USB_SLOW | -------------------------------------------------- EXTCON_MICROPHONE | EXTCON_JACK_MICROPHONE | EXTCON_HEADPHONE | EXTCON_JACK_HEADPHONE | EXTCON_LINE_IN | EXTCON_JACK_LINE_IN | EXTCON_LINE_OUT | EXTCON_JACK_LINE_OUT | EXTCON_VIDEO_IN | EXTCON_JACK_VIDEO_IN | EXTCON_VIDEO_OUT | EXTCON_JACK_VIDEO_OUT | EXTCON_SPDIF_IN | EXTCON_JACK_SPDIF_IN | EXTCON_SPDIF_OUT | EXTCON_JACK_SPDIF_OUT | -------------------------------------------------- EXTCON_HMDI | EXTCON_DISP_HDMI | EXTCON_MHL | EXTCON_DISP_MHL | EXTCON_DVI | EXTCON_DISP_DVI | EXTCON_VGA | EXTCON_DISP_VGA | -------------------------------------------------- And, when altering the name of USB charger connector, EXTCON refers to the "Battery Charging v1.2 Spec and Adopters Agreement"[1] to use the standard name of USB charging port as following. Following name of USB charging port are already used in power_supply subsystem. We chan check it on patch[2]. - EXTCON_CHG_USB_SDP /* Standard Downstream Port */ - EXTCON_CHG_USB_DCP /* Dedicated Charging Port */ - EXTCON_CHG_USB_CDP /* Charging Downstream Port */ - EXTCON_CHG_USB_ACA /* Accessory Charger Adapter */ [1] www.usb.org/developers/docs/devclass_docs/BCv1.2_070312.zip [2] commit 85efc8a18ced ("power_supply: Add types for USB chargers") Signed-off-by: Chanwoo Choi [ckeepax: For the Arizona changes] Acked-by: Charles Keepax Reviewed-by: Roger Quadros

extcon: Redefine the unique id of supported external connectors without 'enum extcon' type

2015-06-13T00:01:42Z

This patch just redefine the unique id of supported external connectors without 'enum extcon' type. Because unique id would be used on devictree file(*.dts) to indicate the specific external connectors like key number of input framework. So, I have the plan to move this definitions to following header file which includes the unique id of supported external connectors. - include/dt-bindings/extcon/extcon.h Fixes: 2a9de9c0f08d ("extcon: Use the unique id for external connector instead of string") Signed-off-by: Chanwoo Choi Signed-off-by: Greg Kroah-Hartman

extcon: Use the unique id for external connector instead of string

2015-05-22T09:58:44Z

This patch uses the unique id to identify the type of external connector instead of string name. The string name have the many potential issues. So, this patch defines the 'extcon' enumeration which includes all supported external connector on EXTCON subsystem. If new external connector is necessary, the unique id of new connector have to be added in 'extcon' enumeration. There are current supported external connector in 'enum extcon' as following: enum extcon { EXTCON_NONE = 0x0, /* USB external connector */ EXTCON_USB = 0x1, EXTCON_USB_HOST = 0x2, /* Charger external connector */ EXTCON_TA = 0x10, EXTCON_FAST_CHARGER = 0x11, EXTCON_SLOW_CHARGER = 0x12, EXTCON_CHARGE_DOWNSTREAM = 0x13, /* Audio and video external connector */ EXTCON_LINE_IN = 0x20, EXTCON_LINE_OUT = 0x21, EXTCON_MICROPHONE = 0x22, EXTCON_HEADPHONE = 0x23, EXTCON_HDMI = 0x30, EXTCON_MHL = 0x31, EXTCON_DVI = 0x32, EXTCON_VGA = 0x33, EXTCON_SPDIF_IN = 0x34, EXTCON_SPDIF_OUT = 0x35, EXTCON_VIDEO_IN = 0x36, EXTCON_VIDEO_OUT = 0x37, /* Miscellaneous external connector */ EXTCON_DOCK = 0x50, EXTCON_JIG = 0x51, EXTCON_MECHANICAL = 0x52, EXTCON_END, }; For example in extcon-arizona.c: To use unique id removes the potential issue about handling the inconsistent name of external connector with string. - Previously, use the string to register the type of arizona jack connector static const char *arizona_cable[] = { "Mechanical", "Microphone", "Headphone", "Line-out", }; - Newly, use the unique id to register the type of arizona jack connector static const enum extcon arizona_cable[] = { EXTCON_MECHANICAL, EXTCON_MICROPHONE, EXTCON_HEADPHONE, EXTCON_LINE_OUT, EXTCON_NONE, }; And this patch modify the prototype of extcon_{get|set}_cable_state_() which uses the 'enum extcon id' instead of 'cable_index'. Because although one more extcon drivers support USB cable, each extcon driver might has the differnt 'cable_index' for USB cable. All extcon drivers can use the unique id number for same external connector with modified extcon_{get|set}_cable_state_(). - Previously, use 'cable_index' on these functions: extcon_get_cable_state_(struct extcon_dev*, int cable_index) extcon_set_cable_state_(struct extcon_dev*, int cable_index, bool state) -Newly, use 'enum extcon id' on these functions: extcon_get_cable_state_(struct extcon_dev*, enum extcon id) extcon_set_cable_state_(struct extcon_dev*, enum extcon id, bool state) Cc: Arnd Bergmann Cc: Felipe Balbi Signed-off-by: Chanwoo Choi Acked-by: Roger Quadros Acked-by: Charles Keepax Acked-by: Ramakrishna Pallala Reviewed-by: Krzysztof Kozlowski [arnd: Report the build break about drivers/usb/phy/phy-tahvo.c after using the unique id for external connector insteadf of string] Reported-by: Arnd Bergmann [dan.carpenter: Report the build warning of extcon_{set|get}_cable_state_()] Reported-by: Dan Carpenter