kernel/drivers/bluetooth, branch linux-5.12.y

Bluetooth: btusb: fix bt fiwmare downloading failure issue for qca btsoc.

2021-07-19T08:01:11Z

[ Upstream commit 4f00bfb372674d586c4a261bfc595cbce101fbb6 ] This is btsoc timing issue, after host start to downloading bt firmware, ep2 need time to switch from function acl to function dfu, so host add 20ms delay as workaround. Signed-off-by: Tim Jiang Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btusb: use default nvm if boardID is 0 for wcn6855.

2021-07-19T08:01:10Z

[ Upstream commit ca17a5cccf8b6d35dab4729bea8f4350bc0b4caf ] if boardID is 0, will use the default nvm file without surfix. Signed-off-by: Tim Jiang Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btusb: Add support USB ALT 3 for WBS

2021-07-19T08:01:10Z

[ Upstream commit e848dbd364aca44c9d23c04bef964fab79e2b34f ] Because mSBC frames do not need to be aligned to the SCO packet boundary. Using USB ALT 3 let HCI payload >= 60 bytes, let mSBC data satisfy 60 Bytes avoid payload unaligned situation and fixed some headset no voise issue. USB Alt 3 supported also need HFP support transparent MTU in 72 Bytes. Signed-off-by: Hilda Wu Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btusb: Add a new QCA_ROME device (0cf3:e500)

2021-07-19T08:01:09Z

[ Upstream commit 0324d19cb99804d99e42c990b8b1e191575a091b ] This patch adds the 0cf3:e500 Bluetooth device (from a QCA9377 board) as a QCA_ROME device. It appears to be functionally identical to another device ID, also from a QCA9377 board, which was previously marked as QCA_ROME in 0a03f98b98c201191e3ba15a0e33f46d8660e1fd ("Bluetooth: Add a new 04ca:3015 QCA_ROME device"). Without this patch, the WiFi side of the QCA9377 board is slow or unusable when the Bluetooth side is in use. See https://askubuntu.com/a/1137852 for another report of QCA_ROME fixing this issue for this device ID. /sys/kernel/debug/usb/devices: T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e500 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Daniel Lenski Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btusb: Fixed too many in-token issue for Mediatek Chip.

2021-07-19T08:01:09Z

[ Upstream commit 8454ed9ff9647e31e061fb5eb2e39ce79bc5e960 ] This patch reduce in-token during download patch procedure. Don't submit urb for polling event before sending hci command. Signed-off-by: mark-yw.chen Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btqca: Don't modify firmware contents in-place

2021-07-14T14:58:58Z

commit b43ca511178ed0ab6fd2405df28cf9e100273020 upstream. struct firmware::data is marked const, and when the firmware is compressed with xz (default at least with Fedora) it's mapped read-only which results in a crash: BUG: unable to handle page fault for address: ffffae57c0ca5047 PGD 100000067 P4D 100000067 PUD 1001ce067 PMD 10165a067 PTE 8000000112bba161 Oops: 0003 [#1] SMP NOPTI CPU: 3 PID: 204 Comm: kworker/u17:0 Not tainted 5.12.1-test+ #1 Hardware name: Dell Inc. XPS 13 9310/0F7M4C, BIOS 1.2.5 12/10/2020 Workqueue: hci0 hci_power_on [bluetooth] RIP: 0010:qca_download_firmware+0x27c/0x4e0 [btqca] Code: 1b 75 04 80 48 0c 01 0f b7 c6 8d 54 02 0c 41 39 d7 0f 8e 62 fe ff ff 48 63 c2 4c 01 e8 0f b7 38 0f b7 70 02 66 83 ff 11 75 d3 <80> 48 0c 80 41 83 fc 03 7e 6e 88 58 0d eb ce 41 0f b6 45 0e 48 8b RSP: 0018:ffffae57c08dfc68 EFLAGS: 00010246 RAX: ffffae57c0ca503b RBX: 000000000000000e RCX: 0000000000000000 RDX: 0000000000000037 RSI: 0000000000000006 RDI: 0000000000000011 RBP: ffff978d9949e000 R08: ffff978d84ed7540 R09: ffffae57c0ca5000 R10: 000000000010cd00 R11: 0000000000000001 R12: 0000000000000005 R13: ffffae57c0ca5004 R14: ffff978d98ca8680 R15: 00000000000016a9 FS: 0000000000000000(0000) GS:ffff9794ef6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffae57c0ca5047 CR3: 0000000113d5a004 CR4: 0000000000770ee0 PKRU: 55555554 Call Trace: qca_uart_setup+0x2cb/0x1390 [btqca] ? qca_read_soc_version+0x136/0x220 [btqca] qca_setup+0x288/0xab0 [hci_uart] hci_dev_do_open+0x1f3/0x780 [bluetooth] ? try_to_wake_up+0x1c1/0x4f0 hci_power_on+0x3f/0x200 [bluetooth] process_one_work+0x1ec/0x380 worker_thread+0x53/0x3e0 ? process_one_work+0x380/0x380 kthread+0x11b/0x140 ? kthread_associate_blkcg+0xa0/0xa0 ret_from_fork+0x1f/0x30 Modules linked in: llc ip_set nf_tables nfnetlink snd_soc_skl_hda_dsp(+) ip6table_filter snd_soc_hdac_hdmi ip6_tables qrtr_mhi iptable_filter snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic s> dell_wmi_sysman(+) dell_smbios snd dcdbas mhi vfat videobuf2_vmalloc i2c_i801 videobuf2_memops videobuf2_v4l2 dell_wmi_descriptor fat wmi_bmof soundcore i2c_smbus videobuf2_common libarc4 mei_me mei hid_se> i2c_hid_acpi i2c_hid video pinctrl_tigerlake fuse CR2: ffffae57c0ca5047 This also seems to fix a failure to suspend due to the firmware download on bootup getting interrupted by the crash: Bluetooth: hci0: SSR or FW download time out PM: dpm_run_callback(): acpi_subsys_suspend+0x0/0x60 returns -110 PM: Device serial0-0 failed to suspend: error -110 PM: Some devices failed to suspend, or early wake event detected Fixes: 83e8196 ("Bluetooth: btqca: Introduce generic QCA ROME support") Cc: Venkata Lakshmi Narayana Gubba Cc: stable@vger.kernel.org Signed-off-by: Connor Abbott Signed-off-by: Marcel Holtmann Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_qca: fix potential GPF

2021-07-14T14:58:58Z

commit 59f90f1351282ea2dbd0c59098fd9bb2634e920e upstream. In qca_power_shutdown() qcadev local variable is initialized by hu->serdev.dev private data, but hu->serdev can be NULL and there is a check for it. Since, qcadev is not used before if (!hu->serdev) return; we can move its initialization after this "if" to prevent GPF. Fixes: 5559904ccc08 ("Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()") Cc: stable@vger.kernel.org # v5.6+ Cc: Rocky Liao Signed-off-by: Pavel Skripkin Reviewed-by: Johan Hovold Signed-off-by: Marcel Holtmann Signed-off-by: Greg Kroah-Hartman

Bluetooth: Add a new USB ID for RTL8822CE

2021-06-18T08:02:50Z

[ Upstream commit 4d96d3b0efee6416ef0d61b76aaac6f4a2e15b12 ] Some models of the RTL8822ce utilize a different USB ID. Add this new one to the Bluetooth driver. Signed-off-by: Larry Finger Signed-off-by: Linus Torvalds Signed-off-by: Sasha Levin

Bluetooth: btusb: Enable quirk boolean flag for Mediatek Chip.

2021-05-19T08:56:13Z

[ Upstream commit 27e554a4fcd84e499bf0a82122b8c4c3f1de38b6 ] Adding support LE scatternet and WBS for Mediatek Chip Signed-off-by: mark-yw.chen Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: btusb: Revert Fix the autosuspend enable and disable

2021-04-09T16:08:02Z

drivers/usb/core/hub.c: usb_new_device() contains the following: /* By default, forbid autosuspend for all devices. It will be * allowed for hubs during binding. */ usb_disable_autosuspend(udev); So for anything which is not a hub, such as btusb devices, autosuspend is disabled by default and we must call usb_enable_autosuspend(udev) to enable it. This means that the "Fix the autosuspend enable and disable" commit, which drops the usb_enable_autosuspend() call when the enable_autosuspend module option is true, is completely wrong, revert it. This reverts commit 7bd9fb058d77213130e4b3e594115c028b708e7e. Cc: Hui Wang Fixes: 7bd9fb058d77 ("Bluetooth: btusb: Fix the autosuspend enable and disable") Acked-by: Hui Wang Acked-by: Marcel Holtmann Signed-off-by: Hans de Goede Signed-off-by: Linus Torvalds