kernel/drivers/acpi/wakeup.c, branch 0x221E-v0.0.1-v6.19

ACPI: wakeup: Drop unneeded casting for sleep_state

2025-06-26T19:08:13Z

Back to the original patch [1] sleep_state was defined as a custom acpi_integer type variable. Nowadays it's plain u64. No need to have casting for it anymore. Link: https://bugzilla.kernel.org/show_bug.cgi?id=1415 [1] Signed-off-by: Andy Shevchenko Link: https://patch.msgid.link/20250612201321.3536493-2-andriy.shevchenko@linux.intel.com Signed-off-by: Rafael J. Wysocki

ACPI: Fix whitespace inconsistencies

2020-11-09T18:08:06Z

Replaces spaces with tabs where spaces have been (inconsistently) used for indentation and removes trailing whitespaces. Signed-off-by: Maximilian Luz Signed-off-by: Rafael J. Wysocki

ACPI: wakeup: Remove dead ACPICA debug code

2020-09-25T16:25:51Z

The ACPICA debug code of ACPI_SYSTEM_COMPONENT and ACPI_MODULE_NAME() is not used in wakeup.c, remove it. Signed-off-by: Hanjun Guo [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki

ACPI: PM: Add acpi_[un]register_wakeup_handler()

2020-04-04T17:45:18Z

Since commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") the SCI triggering without there being a wakeup cause recognized by the ACPI sleep code will no longer wakeup the system. This works as intended, but this is a problem for devices where the SCI is shared with another device which is also a wakeup source. In the past these, from the pov of the ACPI sleep code, spurious SCIs would still cause a wakeup so the wakeup from the device sharing the interrupt would actually wakeup the system. This now no longer works. This is a problem on e.g. Bay Trail-T and Cherry Trail devices where some peripherals (typically the XHCI controller) can signal a Power Management Event (PME) to the Power Management Controller (PMC) to wakeup the system, this uses the same interrupt as the SCI. These wakeups are handled through a special INT0002 ACPI device which checks for events in the GPE0a_STS for this and takes care of acking the PME so that the shared interrupt stops triggering. The change to the ACPI sleep code to ignore the spurious SCI, causes the system to no longer wakeup on these PME events. To make things worse this means that the INT0002 device driver interrupt handler will no longer run, causing the PME to not get cleared and resulting in the system hanging. Trying to wakeup the system after such a PME through e.g. the power button no longer works. Add an acpi_register_wakeup_handler() function which registers a handler to be called from acpi_s2idle_wake() and when the handler returns true, return true from acpi_s2idle_wake(). The INT0002 driver will use this mechanism to check the GPE0a_STS register from acpi_s2idle_wake() and to tell the system to wakeup if a PME is signaled in the register. Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Cc: 5.4+ # 5.4+ Signed-off-by: Hans de Goede Signed-off-by: Rafael J. Wysocki

ACPI: list_for_each_safe() -> list_for_each_entry_safe()

2020-03-04T09:48:00Z

Replace list_for_each_safe() and open-coded list entry address computations with list_for_each_entry_safe() in several places to simplify code. Signed-off-by: chenqiwu [ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

ACPI: Clean up inclusions of ACPI header files

2013-12-07T00:03:14Z

Replace direct inclusions of , and , which are incorrect, with inclusions and remove some inclusions of those files that aren't necessary. First of all, , and should not be included directly from any files that are built for CONFIG_ACPI unset, because that generally leads to build warnings about undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set, includes those files and for CONFIG_ACPI unset it provides stub ACPI symbols to be used in that case. Second, there are ordering dependencies between those files that always have to be met. Namely, it is required that be included prior to so that the acpi_pci_root declarations the latter depends on are always there. And which provides basic ACPICA type declarations should always be included prior to any other ACPI headers in CONFIG_ACPI builds. That also is taken care of including as appropriate. Signed-off-by: Lv Zheng Cc: Greg Kroah-Hartman Cc: Matthew Garrett Cc: Tony Luck Cc: "H. Peter Anvin" Acked-by: Bjorn Helgaas (drivers/pci stuff) Acked-by: Konrad Rzeszutek Wilk (Xen stuff) Signed-off-by: Rafael J. Wysocki

ACPI / Wakeup: Enable button GPEs unconditionally during initialization

2011-02-12T00:39:53Z

Commit 9630bdd (ACPI: Use GPE reference counting to support shared GPEs) introduced a suspend regression where boxes resume immediately after being suspended due to the lid or sleep button wakeup status not being cleared properly. This happens if the GPEs corresponding to those devices are not enabled all the time, which apparently is expected by some BIOSes. To fix this problem, enable button and lid GPEs unconditionally during initialization and keep them enabled all the time, regardless of whether or not the ACPI button driver is used. References: https://bugzilla.kernel.org/show_bug.cgi?id=27372 Reported-and-tested-by: Ferenc Wágner Cc: stable@kernel.org Signed-off-by: Rafael J. Wysocki

Merge branch 'wakeup-etc-rafael' into release

2011-01-12T09:55:46Z

ACPICA: Rename some function and variable names

2011-01-12T09:24:40Z

Some function and variable names are renamed to be consistent with ACPICA code base. acpi_raw_enable_gpe -> acpi_ev_add_gpe_reference acpi_raw_disable_gpe -> acpi_ev_remove_gpe_reference acpi_gpe_can_wake -> acpi_setup_gpe_for_wake acpi_gpe_wakeup -> acpi_set_gpe_wake_mask acpi_update_gpes -> acpi_update_all_gpes acpi_all_gpes_initialized -> acpi_gbl_all_gpes_initialized acpi_handler_info -> acpi_gpe_handler_info ... Signed-off-by: Lin Ming Signed-off-by: Len Brown