kernel/arch/powerpc/boot/dts/mpc8378_rdb.dts, branch linux-6.2.y

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

2019-05-30T18:26:32Z

Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman

powerpc/83xx: Add generic compatible string for I2C EEPROM

2017-06-28T03:08:14Z

The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas Signed-off-by: Michael Ellerman

powerpc: use the new LED disk activity trigger

2016-06-27T06:58:40Z

- dts: rename 'ide-disk' to 'disk-activity' - defconfig: rename 'ADB_PMU_LED_IDE' to 'ADB_PMU_LED_DISK' Cc: Joseph Jezak Cc: Jörg Sommer Signed-off-by: Stephan Linz Signed-off-by: Jacek Anaszewski

dt/bindings: Remove all references to device_type "ethernet-phy"

2014-01-16T11:11:51Z

The device_type property is deprecated for the flattened device tree and the value "ethernet-phy" has never been defined as having a useful meaning. Neither the kernel nor u-boot depend on it. It should never have appeared in PHY bindings. This patch removes all references to "ethernet-phy" as a device_type value from the documentation and the .dts files. This patch was generated mechanically with the following command and then verified by looking at the diff. sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'` Signed-off-by: Grant Likely Acked-by: Srinivas Kandagatla Cc: Rob Herring Cc: Pawel Moll Cc: Mark Rutland Cc: Ian Campbell Cc: Kumar Gala Cc: Florian Fainelli Cc: Benjamin Herrenschmidt

powerpc/fsl: update compatiable on fsl 16550 uart nodes

2012-01-04T21:38:40Z

The Freescale serial port's are pretty much a 16550, however there are some FSL specific bugs and features. Add a "fsl,ns16550" compatiable string to allow code to handle those FSL specific issues. Signed-off-by: Kumar Gala

powerpc/83xx: Add MCU LEDs support for MPC837xRDB and MPC8315RDB boards

2010-05-17T15:55:32Z

There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR and HDD. After adding appropriate nodes we can program these LEDs from kernel and user space. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala

powerpc: introduce and document sdhci,wp-inverted property for eSDHC

2009-09-23T14:39:37Z

eSDHC block in MPC837x SOCs reports inverted write-protect state, soon sdhci-of driver will look for sdhci,wp-inverted properties to decide whether apply a specific quirk. So, document the property and add it to device tree source files. Signed-off-by: Anton Vorontsov Cc: Pierre Ossman Cc: Kumar Gala Cc: David Vrabel Cc: Ben Dooks Cc: Sascha Hauer Cc: Benjamin Herrenschmidt Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

powerpc/83xx: Add eSDHC support for MPC837xE-RDB/WLAN boards

2009-08-20T00:27:51Z

Actually, the support is already there, but it requires newer U-Boots (to fill-in clock-frequency, and setup pin multiplexing). Though, it appears that on RDB boards USBB pins aren't multiplexed between USB and eSDHC (unlike MDS boards, where USB and eSDHC share pctl and pwrfault pins). So, for RDB boards we can safely setup pinmux and manually fill-in clock-frequency, thus making eSDHC work even with older u-boots. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala Signed-off-by: Benjamin Herrenschmidt

powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards

2009-07-30T04:18:41Z

U-Boot maps PCI IO at 0xe0300000, while current dts files specify 0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y. 8139too Fast Ethernet driver 0.9.28 Machine check in kernel mode. Caused by (from SRR1=41000): Transfer error ack signal Oops: Machine check, sig: 7 [#1] MPC837x RDB [...] NIP [00000900] 0x900 LR [c0439df8] rtl8139_init_board+0x238/0x524 Call Trace: [cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable) [cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c [cf831e40] [c0235250] pci_call_probe+0x20/0x30 [...] This patch fixes the issue by specifying the correct PCI IO base address. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala

powerpc/83xx: Update sdhci nodes per new bindings

2009-06-16T02:45:30Z

As of commit 404614728f857d0ac63d29c3a29d0cf392a15598 ("Update FSL esdhc binding"), we use "fsl,esdhc" compatible entry as a base match. U-Boot will use the same compatible to fixup esdhc nodes. This patch updates 83xx dts files so that they conform to the new bindings. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala