kernel/arch/powerpc/boot/dts/mpc8349emitx.dts, branch linux-4.3.y

dt/bindings: Remove all references to device_type "ethernet-phy"

2014-01-16T11:11:51Z

The device_type property is deprecated for the flattened device tree and the value "ethernet-phy" has never been defined as having a useful meaning. Neither the kernel nor u-boot depend on it. It should never have appeared in PHY bindings. This patch removes all references to "ethernet-phy" as a device_type value from the documentation and the .dts files. This patch was generated mechanically with the following command and then verified by looking at the diff. sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'` Signed-off-by: Grant Likely Acked-by: Srinivas Kandagatla Cc: Rob Herring Cc: Pawel Moll Cc: Mark Rutland Cc: Ian Campbell Cc: Kumar Gala Cc: Florian Fainelli Cc: Benjamin Herrenschmidt

powerpc/fsl: update compatiable on fsl 16550 uart nodes

2012-01-04T21:38:40Z

The Freescale serial port's are pretty much a 16550, however there are some FSL specific bugs and features. Add a "fsl,ns16550" compatiable string to allow code to handle those FSL specific issues. Signed-off-by: Kumar Gala

powerpc/mpc8349emitx: mark localbus as compatible with simple-bus

2011-10-07T04:32:57Z

Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala

powerpc/83xx: mpc8349emitx - add leds-gpio binding

2009-12-09T21:15:54Z

Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala

powerpc/83xx: mpc8349emitx - add OF descriptions of LocalBus devices

2009-12-09T21:15:45Z

Describe all LocalBus chipselects on MPC8349E-MITX board. Also add flash bindings. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala

powerpc/83xx: mpc8349emitx - populate I2C busses in device tree

2009-12-09T21:15:36Z

Add OF descriptions of EEPROM, two GPIO extenders and SPD hanging on I2C on this board. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala

powerpc/83xx: mpc8349emitx - add gpio controller declarations

2009-12-09T21:15:22Z

mpc8349 bears two GPIO controllers. Enable support for them. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala

powerpc/mpc83xx: Fix usb mux setup for mpc834x

2009-06-16T02:45:31Z

usb0 and usb1 mux settings in the sicrl register were swapped (twice!) in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci and full speed devices. The USB port config on mpc834x is done using 2 muxes: Port 0 is always used for MPH port 0, and port 1 can either be used for MPH port 1 or DR (unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM figure 1-4.. mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit positions of the usb0 / usb1 mux settings swapped. It would basically work if you specified port1 instead of port0 for the MPH controller (and happened to use ULPI phys), which is what all the 834x dts have done, even though that configuration is physically invalid. Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality. Signed-off-by: Peter Korsgaard Signed-off-by: Kumar Gala

powerpc/fsl: Remove cell-index from PCI nodes

2009-05-19T05:46:14Z

The cell-index property isn't used on PCI nodes and is ill defined. Remove it for now and if someone comes up with a good reason and consistent definition for it we can add it back Signed-off-by: Kumar Gala

powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes

2009-03-24T13:35:04Z

Currently it doesn't matter where the mdio nodes are placed, but with power management support (i.e. when sleep = <> properties will take effect), mdio nodes placement will become important: mdio controller is a part of the ethernet block, so the mdio nodes should be placed correctly. Otherwise we may wrongly assume that MDIO controllers are available during sleep. Suggested-by: Scott Wood Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala