kernel/arch/powerpc/boot/dts/lite5200.dts, branch linux-4.3.y

powerpc/5200: fix lite5200 ethernet phy address

2010-06-15T20:47:04Z

According to my schematics, on Lite5200 board ethernet phy uses address 0 (all ADDR lines are pulled down). With this change I can talk to onboard phy (LXT971) and correctly use autonegotiation. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Grant Likely

powerpc/5200: add lite5200 onboard I2C eeprom and flash

2010-06-15T06:04:31Z

Add dts descriptions for onboard 256 byte I2C eeprom (pcf8582C-2) and 16MB NOR flash (am29lv652d). Signed-off-by: Dmitry Eremin-Solenikov [grant.likely@secretlab.ca: added lite5200b eeprom and declared lite5200 gpios] Signed-off-by: Grant Likely

powerpc/boot/dts: drop obsolete 'fsl5200-clocking'

2009-10-15T15:58:27Z

The 'fsl5200-clocking'-property was dropped since 0d1cde235874b00905bce23f659690d060ebf475. Remove all occurences in dts-files. Signed-off-by: Wolfram Sang Signed-off-by: Grant Likely

powerpc/5200: Trim cruft from device trees

2009-02-03T19:30:26Z

Trim out obsolete/extraneous properties and tighten up some usage conventions. Changes include: - removal of device_type properties - removal of cell-index properties - Addition of gpio-controller and #gpio-cells properties to gpio nodes - Move common interrupt-parent property out of device nodes and into top level parent node. This patch also include what looks to be just trivial editorial whitespace/format changes, but there is real method in this madness. Editorial changes were made to keep the all the mpc5200 board device trees as similar as possible so that diffs between them only show the real differences between the boards. The pcm030 device tree was most affected by this because many of the comments had been changed from // to /* */ style and some cell values where changed from decimal to hex format when it was cloned from one of the other 5200 device trees. Signed-off-by: Grant Likely Reviewed-by: Wolfram Sang

powerpc: Remove device_type = "rtc" properties in .dts files

2008-11-05T11:08:28Z

We don't want to encourage the device_type usage. It isn't used in the code, so we can simply remove it from the dts files. Suggested-by: Scott Wood Signed-off-by: Anton Vorontsov Acked-by: Grant Likely Acked-by: David Gibson Signed-off-by: Paul Mackerras

[POWERPC] mpc5200: Switch mpc5200 dts files to dts-v1 format

2008-04-29T13:19:07Z

Signed-off-by: Grant Likely

[POWERPC] Fix MPC5200 (not B!) device tree so FEC ethernet works

2008-04-03T11:11:12Z

This gets the FEC ethernet driver working again on the lite5200 platform. The FEC driver is also compatible with the MPC5200, not only with the MPC5200B, so this adds a suitable entry to the driver's match list. Furthermore this adds the settings for the PHY in the dts file for the Lite5200. Note, that this is not exactly the same as in the Lite5200B, because the PHY is located at f0003000:01 for the 5200, and at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B, both booted a kernel via tftp and mounted the root via nfs successfully. Signed-off-by: René Bürgel Acked-by: Grant Likely Signed-off-by: Paul Mackerras

[POWERPC] mpc5200: make dts files conform to generic names recommended practice

2008-01-26T22:32:11Z

Modify mpc5200 dts files to match Open Firmware's Generic Names recommended practice. Signed-off-by: Grant Likely

[POWERPC] mpc5200: add #address-cells and #size-cells to soc node.

2008-01-26T21:03:46Z

The various 5200 dts files don't have values specified for the soc node, which in turn results in a warning from the processing of every child node (roughly 40 warnings per file). This explicitly sets the default values and gets rid of all the warnings. Signed-off-by: Paul Gortmaker Signed-off-by: Grant Likely

[POWERPC] mpc5200: Add generic support for simple MPC5200 based boards

2008-01-19T03:57:09Z

This patch adds support for 'mpc5200-simple-platform' compatible boards which do not need a platform specific setup. Such boards are supported assuming the following: - GPIO pins are configured by the firmware, - CDM configuration (clocking) is setup correctly by firmware, - if the 'fsl,has-wdt' property is present in one of the gpt nodes, then it is safe to use such gpt to reset the board, - PCI is supported if enabled in the kernel configuration and if there is a PCI bus node defined in the device tree. Signed-off-by: Marian Balakowicz Signed-off-by: Grant Likely