kernel/Documentation/devicetree/bindings/serial/rs485.yaml, branch linux-6.2.y

dt-bindings: drop redundant part of title (end, part three)

2022-12-16T17:41:49Z

The Devicetree bindings document does not have to say in the title that it is a "binding", but instead just describe the hardware. Drop trailing "bindings" in various forms (also with trailing full stop): find Documentation/devicetree/bindings/ -type f -name '*.yaml' \ -not -name 'trivial-devices.yaml' \ -exec sed -i -e 's/^title: $.*$ [bB]indings\?\.\?$/title: \1/' {} \; Signed-off-by: Krzysztof Kozlowski Acked-by: Alexandre Belloni Acked-by: Matti Vaittinen # ROHM Acked-by: Ulf Hansson # MMC Acked-by: Stephen Boyd # clk Acked-by: Dmitry Torokhov # input Acked-by: Mark Brown Acked-by: Hans Verkuil # media Acked-by: Sebastian Reichel # power Acked-by: Viresh Kumar # cpufreq Link: https://lore.kernel.org/r/20221216163815.522628-7-krzysztof.kozlowski@linaro.org Signed-off-by: Rob Herring

dt_bindings: rs485: Correct delay values

2022-07-14T14:34:24Z

Currently the documentation claims that a maximum of 1000 msecs is allowed for RTS delays. However nothing actually checks the values read from device tree/ACPI and so it is possible to set much higher values. There is already a maximum of 100 ms enforced for RTS delays that are set via the UART TIOCSRS485 ioctl. To be consistent with that use the same limit for DT/ACPI values. Although this change is visible to userspace the risk of breaking anything when reducing the max delays from 1000 to 100 ms should be very low, since 100 ms is already a very high maximum for delays that are usually rather in the usecs range. Acked-by: Rob Herring Signed-off-by: Lino Sanfilippo Link: https://lore.kernel.org/r/20220710164442.2958979-7-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman

dt_bindings: rs485: Add receiver enable polarity

2022-04-26T12:47:38Z

Add polarity property for receiver enable. Some UARTs have separate enable pins for tx (RTS or DE) and rx (RE). As most RS485 transceivers have !RE pin, the default is active low in contrast to rs485-rts-active-low that defaults to active high. Cc: devicetree@vger.kernel.org Reviewed-by: Rob Herring Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20220426122448.38997-4-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman

dt-bindings: Explicitly allow additional properties in common schemas

2020-10-07T16:30:06Z

In order to add meta-schema checks for additional/unevaluatedProperties being present, all schema need to make this explicit. As common/shared schema are included by other schemas, they should always allow for additionalProperties. Acked-by: Mark Brown Acked-by: Krzysztof Kozlowski Acked-by: Sebastian Reichel Acked-by: Chanwoo Choi Acked-By: Vinod Koul Acked-by: Lee Jones Acked-by: Geert Uytterhoeven Acked-by: Srinivas Kandagatla Acked-by: Ulf Hansson Acked-by: Jonathan Cameron Acked-by: Guenter Roeck Link: https://lore.kernel.org/r/20201005183830.486085-5-robh@kernel.org Signed-off-by: Rob Herring

Merge tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2020-06-07T16:52:36Z

Pull tty/serial driver updates from Greg KH: "Here is the tty and serial driver updates for 5.8-rc1 Nothing huge at all, just a lot of little serial driver fixes, updates for new devices and features, and other small things. Full details are in the shortlog. All of these have been in linux-next with no issues for a while" * tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits) tty: serial: qcom_geni_serial: Add 51.2MHz frequency support tty: serial: imx: clear Ageing Timer Interrupt in handler serial: 8250_fintek: Add F81966 Support sc16is7xx: Add flag to activate IrDA mode dt-bindings: sc16is7xx: Add flag to activate IrDA mode serial: 8250: Support rs485 bus termination GPIO serial: 8520_port: Fix function param documentation dt-bindings: serial: Add binding for rs485 bus termination GPIO vt: keyboard: avoid signed integer overflow in k_ascii serial: 8250: Enable 16550A variants by default on non-x86 tty: hvc_console, fix crashes on parallel open/close serial: imx: Initialize lock for non-registered console sc16is7xx: Read the LSR register for basic device presence check sc16is7xx: Allow sharing the IRQ line sc16is7xx: Use threaded IRQ sc16is7xx: Always use falling edge IRQ tty: n_gsm: Fix bogus i++ in gsm_data_kick tty: n_gsm: Remove unnecessary test in gsm_print_packet() serial: stm32: add no_console_suspend support tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP ...

dt-bindings: serial: Add binding for rs485 bus termination GPIO

2020-05-29T10:42:53Z

Commit e8759ad17d41 ("serial: uapi: Add support for bus termination") introduced the ability to enable rs485 bus termination from user space. So far the feature is only used by a single driver, 8250_exar.c, using a hardcoded GPIO pin specific to Siemens IOT2040 products. Provide for a more generic solution by allowing specification of an rs485 bus termination GPIO pin in the device tree. An upcoming commit implements support for this pin for any 8250 driver. The binding is used in device trees of the "Revolution Pi" PLCs offered by KUNBUS. [Heiko Stuebner converted the binding to YAML, hence his Signed-off-by.] Signed-off-by: Heiko Stuebner Signed-off-by: Lukas Wunner Cc: Jan Kiszka Reviewed-by: Rob Herring Link: https://lore.kernel.org/r/4f4411895dc52c846f766e7f7207ec412c4811b6.1589811297.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

dt-bindings: Remove cases of 'allOf' containing a '$ref'

2020-05-03T16:10:41Z

json-schema versions draft7 and earlier have a weird behavior in that any keywords combined with a '$ref' are ignored (silently). The correct form was to put a '$ref' under an 'allOf'. This behavior is now changed in the 2019-09 json-schema spec and '$ref' can be mixed with other keywords. The json-schema library doesn't yet support this, but the tooling now does a fixup for this and either way works. This has been a constant source of review comments, so let's change this treewide so everyone copies the simpler syntax. Scripted with ruamel.yaml with some manual fixups. Some minor whitespace changes from the script. Signed-off-by: Rob Herring Acked-by: Maxime Ripard Acked-by: Lee Jones Acked-By: Vinod Koul Acked-by: Mark Brown Acked-by: Alexandre Belloni Acked-by: Wolfram Sang # for I2C Reviewed-by: Linus Walleij Acked-by: Jonathan Cameron #for-iio Reviewed-by: Stephen Boyd # clock Signed-off-by: Rob Herring

dt-bindings: Clean-up schema indentation formatting

2020-04-16T21:59:22Z

Fix various inconsistencies in schema indentation. Most of these are list indentation which should be 2 spaces more than the start of the enclosing keyword. This doesn't matter functionally, but affects running scripts which do transforms on the schema files. Signed-off-by: Rob Herring Acked-by: Maxime Ripard Acked-by: Lee Jones Acked-By: Vinod Koul Acked-by: Mark Brown Acked-by: Alexandre Belloni Signed-off-by: Rob Herring

dt-bindings: serial: Convert rs485 bindings to json-schema

2020-01-23T20:34:15Z

Convert rs485 binding to yaml style file. Signed-off-by: Benjamin Gaignard Signed-off-by: Rob Herring