kernel/Documentation/devicetree/bindings/regulator, branch linux-5.1.y

dt-bindings: regulator: tps65218: rectify units of LS3

2019-02-26T11:49:52Z

LS3 has a selectable current limit. Change units to microamp in the example. Signed-off-by: Christian Hohnstaedt Signed-off-by: Mark Brown

dt-bindings: regulator: add LS2 load switch documentation

2019-02-26T11:49:34Z

Document device-tree settings of the load-switch LS2 in the tps65218 device. Signed-off-by: Christian Hohnstaedt Signed-off-by: Mark Brown

regulator: fan53555: Add support for FAN53526

2019-02-21T11:41:04Z

The FAN53526 differs from the FAN53555 only in that the mode bit in VSEL0/VSEL1 is moved to the CONTROL register, the voltage selector mask is extended by 1 bit and the step is different. So extend the existing fan53555 driver to support FAN53526 as well. Signed-off-by: Bjorn Andersson Signed-off-by: Mark Brown

dt-bindings: regulator: Add active discharge support for stpmic1

2019-02-19T11:02:46Z

Add support for active discharge for USB power switches. Signed-off-by: pascal paillet Signed-off-by: Mark Brown

dt-bindings: regulator: remove regulator pull-down support for stpmic1

2019-02-19T11:02:27Z

Regulator high pull down are enabled by default so remove support in the driver. Signed-off-by: Pascal Paillet Signed-off-by: Mark Brown

dt-bindings: regulator: remove interrupt-parent description on stpmic1

2019-02-19T11:02:08Z

The interrupt parent description is not needed as the parent is a parent node with 'interrupt-controller' property. Signed-off-by: pascal paillet Signed-off-by: Mark Brown

devicetree: bindings: bd718x7: document HW state related ROHM specific properties

2019-02-14T15:10:40Z

Add ROHM BD71837 / BD71847 specific device tree bindings for controlling the PMIC shutdown/reset states and voltages for different HW states. The PMIC was designed to be used with NXP i.MX8 SoC and it supports SNVS low power state which seems to be typical for NXP i.MX SoCs. However, when SNVS is used we must not allow SW to control enabling/disabling those regulators which are crucial for system to boot as there is a HW limitation which causes SW controlled regulators to be kept shut down after SNVS reset. Allow setting the SNVS to be used as reset target state and allow marking those regulators which are critical for boot. Signed-off-by: Matti Vaittinen Tested-by: Angus Ainslie Reviewed-by: Angus Ainslie Signed-off-by: Mark Brown

dt-bindings: regulator: update fixed-regulator example

2019-02-08T16:48:57Z

Fixed regulators do not have associated bus addresses and are typically placed directly under the root node where their names must still be unique despite not having a unit address. Fix the malformed example node which had a unit address but no "reg" property by dropping the unit address. Also, try to make the example more useful by using the recommended generic node name "regulator", but with a suffix reflecting the regulator name in order to make it unique. Signed-off-by: Johan Hovold Signed-off-by: Mark Brown

dt-bindings: regulator: add DT bindings for max77650

2019-01-29T15:22:39Z

Add the DT binding document for max77650 regulators. Signed-off-by: Bartosz Golaszewski Signed-off-by: Mark Brown

regulator: bindings: ROHM bd70528 regulator bindings

2019-01-23T15:51:41Z

ROHM bd70528 is a ultra low power PMIC which includes 3 bucks, 3 LDOs and 2 LED drivers. Document the bindings for them. Signed-off-by: Matti Vaittinen Signed-off-by: Mark Brown