kernel/Documentation/devicetree/bindings/power/reset, branch linux-5.1.y

dt-bindings: soc: Add ZynqMP PM bindings

2019-02-12T12:36:21Z

Add documentation to describe Xilinx ZynqMP power management bindings. Signed-off-by: Rajan Vaja Signed-off-by: Jolly Shah Reviewed-by: Rob Herring Signed-off-by: Michal Simek

power: reset: gpio-poweroff: add ability to specific active and inactive delays

2018-12-05T21:38:29Z

Similar to gpio-reset allow to specify active and inactive delays while keeping the 100ms defaults that were used previously all the time. The dt-properties are named the same as in gpio-reset but get an "-ms" suffix as properties should contain such a suffix specifying its unit. Signed-off-by: Heiko Stuebner Reviewed-by: Rob Herring Reviewed-by: Moritz Fischer Signed-off-by: Sebastian Reichel

power: reset: qcom-pon: Add pms405 pon support

2018-09-20T09:40:00Z

Update the binding and driver for pms405 pon. Signed-off-by: Vinod Koul Signed-off-by: Bjorn Andersson Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: qcom: Add resin binding

2018-07-07T20:22:23Z

Resin is similar to pwrkey, add the description and example for resin bindings Signed-off-by: Vinod Koul Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: Add qcom pon binding

2018-07-06T13:53:10Z

The Power On device for Qcom PM 8xxx is a MFD supporting pwrkey and resin along with the Android reboot-mode. Add the binding describing this. Suggested-by: Bjorn Andersson Reviewed-by: Bjorn Andersson Signed-off-by: Vinod Koul Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: gpio-poweroff: Add 'timeout-ms' property

2018-03-09T16:14:32Z

Add 'timeout-ms' property to support boards where the 3s timeout that the current driver defaults to is too short. Signed-off-by: Moritz Fischer Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: Document ocelot-reset binding

2018-02-12T10:23:46Z

Add binding documentation for the Microsemi Ocelot reset block. Cc: devicetree@vger.kernel.org Cc: linux-pm@vger.kernel.org Signed-off-by: Alexandre Belloni Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

power: reset: remove unused imx-snvs-poweroff driver

2018-01-08T17:09:25Z

There's no user of it in kernel now and it basically functions the same as the generic syscon-poweroff.c to which we have already switched. So let's remove it. Cc: Robin Gong Cc: Shawn Guo Signed-off-by: Dong Aisheng Acked-by: Rob Herring Reviewed-by: Fabio Estevam Signed-off-by: Sebastian Reichel

dt-bindings: Remove leading zeros from bindings notation

2017-11-09T23:05:05Z

Improve the binding example by removing all the leading zeros to fix the following dtc warnings: Warning (unit_address_format): Node /XXX unit name should not have leading 0s Converted using the following command: perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"` Some unnecessary changes were manually fixed. Signed-off-by: Marco Franchi Signed-off-by: Rob Herring

dt-bindings: Remove "status" from examples

2017-09-05T15:03:06Z

Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland Signed-off-by: Rob Herring