kernel/Documentation/devicetree/bindings/net/wireless, branch linux-5.1.y

dt-bindings: net: mt76: update binding for mt7603 driver

2019-02-26T11:29:56Z

In addition to MT7603E PCI devices, the driver supports the WLAN core on MT7628/MT7688, which needs to be defined in DT. Reviewed-by: Rob Herring Signed-off-by: Felix Fietkau

dt-bindings: net: ath10k: add new dt entry to identify external FEM

2018-12-20T17:09:51Z

This adds new dt entry ext-fem-name, it is used by ath10k driver to select correct timing parameters and configure it in target wifi hardware. The Front End Module(FEM) normally includes tx power amplifier(PA) and rx low noise amplifier(LNA). The default timing parameters like tx end to PA off timing values were fine tuned for internal FEM used in reference design. And these timing values can not be same if ODM modifies hardware design with different external FEM. This DT entry helps to choose correct timing values in driver if different external FEM hardware used. Signed-off-by: Bhagavathi Perumal S Reviewed-by: Rob Herring Signed-off-by: Kalle Valo

dt-bindings: net: ath10k: fix node name and device type in qcom ath10k example

2018-12-20T17:09:41Z

In qcom,ath10k documentation, ath10k is used as node name in the example of pci based device. Normally, node name should be class of device and not the model name, so fix it to node name "wifi". And remove the property device_type pci since only pci bridges should have this property. Signed-off-by: Bhagavathi Perumal S Reviewed-by: Rob Herring Signed-off-by: Kalle Valo

dt: bindings: ath10k: add bindings for wifi iommu node

2018-12-20T17:07:39Z

WCN3990 wifi module can optionally make use of the IOMMU. Add binding documentation for phandle to the IOMMU and the stream id of wifi iommu block. Signed-off-by: Govind Singh Reviewed-by: Rob Herring Reviewed-by: Brian Norris Tested-by: Brian Norris Signed-off-by: Kalle Valo

dt: bindings: ath10k: add missing dt properties for WCN3990 wifi node

2018-12-20T17:07:29Z

Add missing optional properties in WCN3990 wifi node. Signed-off-by: Govind Singh Reviewed-by: Rob Herring Reviewed-by: Brian Norris Tested-by: Brian Norris Signed-off-by: Kalle Valo

dt: bindings: add bindings for msa memory region

2018-10-13T17:31:25Z

Add device tree binding documentation details of msa memory region for ath10k qmi client for SDM845/APQ8098 SoC into "qcom,ath10k.txt". Signed-off-by: Govind Singh Reviewed-by: Bjorn Andersson Acked-by: Niklas Cassel Reviewed-by: Brian Norris Reviewed-by: Rob Herring Signed-off-by: Kalle Valo

dt-bindings: remove 'interrupt-parent' from bindings

2018-07-25T20:09:39Z

'interrupt-parent' is often documented as part of define bindings, but it is really outside the scope of a device binding. It's never required in a given node as it is often inherited from a parent node. Or it can be implicit if a parent node is an 'interrupt-controller' node. So remove it from all the binding files. Cc: Mark Rutland Cc: devicetree@vger.kernel.org Signed-off-by: Rob Herring

dt: bindings: add bindings for wcn3990 wifi block

2018-04-19T15:53:10Z

Add device tree binding documentation details for wcn3990 wifi block present in Qualcomm SDM845/APQ8098 SoC into "qcom,ath10k.txt". Signed-off-by: Govind Singh Reviewed-by: Rob Herring Signed-off-by: Kalle Valo

Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git

2017-12-14T16:38:48Z

ath.git patches for 4.16. Major changes: ath10k * enable multiqueue support for all hw using mac80211 wake_tx_queue op * new Kconfig option ATH10K_SPECTRAL to save RAM * show tx stats on QCA9880 * new qcom,ath10k-calibration-variant DT entry * WMI layer support for wcn3990 ath9k * new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM wcn36xx * hardware scan offload support wil6210 * run-time PM support when interface is down

dt: bindings: add new dt entry for ath10k calibration variant

2017-12-14T15:27:48Z

The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct board data file on QCA4019 based devices. Multiple different boards share the same values. Only the original reference designs can currently be identified and loaded from the board-2.bin. But these will not result in the correct calibration data when combined with the pre-calibration data from the device. An additional "variant" information has to be provided (via SMBIOS or DT) to select the correct board data for a design which was modified by an ODM. Signed-off-by: Sven Eckelmann Signed-off-by: Kalle Valo