kernel/Documentation/devicetree/bindings/net/cpsw.txt, branch linux-4.3.y

drivers: net: cpsw: add phy-handle parsing

2015-10-21T13:41:42Z

add the ability to parse "phy-handle". This is needed for phys, which have a DT node, and need to parse DT properties. Signed-off-by: Heiko Schocher Signed-off-by: David S. Miller

Documentation: DT: cpsw: document missing compatible

2015-09-01T13:17:30Z

CPSW driver has multiple compatibles for errata implementations but not documented, add necessary documentation. Signed-off-by: Mugunthan V N Signed-off-by: Rob Herring

net: cpsw: Add am33xx MACID readout

2014-09-30T05:30:43Z

This patch adds a function to get the MACIDs from the am33xx SoC control module registers which hold unique vendor MACIDs. This is only used if of_get_mac_address() fails to get a valid mac address. Signed-off-by: Markus Pargmann Reviewed-by: Wolfram Sang Tested-by: Steven Rostedt Acked-by: Tony Lindgren Signed-off-by: David S. Miller

DT doc: net: cpsw mac-address is optional

2014-09-30T05:30:42Z

mac-address is an optional property. If no mac-address is set, a random mac-address will be generated. Signed-off-by: Markus Pargmann Reviewed-by: Wolfram Sang Signed-off-by: David S. Miller

DT: net: document Ethernet bindings in one place

2014-02-18T22:05:39Z

This patch is an attempt to gather the Ethernet related bindings in one file, like it's done in the MMC and some other subsystems. It should save some of the trouble of documenting several properties over and over in each binding document, instead only making reference to the main file. I have used the Embedded Power Architecture(TM) Platform Requirements (ePAPR) standard as a base for the properties description, also documenting some ad-hoc properties that have been introduced over time despite having direct analogs in ePAPR. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller

drivers: net: ethernet: cpsw: add phy-mode support to cpsw driver

2013-06-04T21:17:22Z

Adding phy-mode support to cpsw driver and updating the cpsw binding documentation. Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller

drivers: net: ethernet: cpsw: change cpts_active_slave to active_slave

2013-03-13T08:38:19Z

Change cpts_active_slave to active_slave so that the same DT property can be used to ethtool and SIOCGMIIPHY. CC: Richard Cochran Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller

documentation: dt: bindings: cpsw: cleanup documentation

2013-03-13T08:38:18Z

Move all the slave note properties to separate section to reduce the confusion between slave note properties and cpsw node properties Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller

driver: net: ethernet: cpsw: dual emac interface implementation

2013-02-12T21:15:10Z

The CPSW switch can act as Dual EMAC by segregating the switch ports using VLAN and port VLAN as per the TRM description in 14.3.2.10.2 Dual Mac Mode Following CPSW components will be common for both the interfaces. * Interrupt source is common for both eth interfaces * Interrupt pacing is common for both interfaces * Hardware statistics is common for all the ports * CPDMA is common for both eth interface * CPTS is common for both the interface and it should not be enabled on both the interface as timestamping information doesn't contain port information. Constrains * Reserved VID of One port should not be used in other interface which will enable switching functionality * Same VID must not be used in both the interface which will enable switching functionality Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller

cpsw: simplify the setup of the register pointers

2012-11-15T03:09:06Z

Instead of having a host of different register offsets in the device tree, this patch simplifies the CPSW code by letting the driver set the proper register offsets automatically, based on the CPSW version. Signed-off-by: Richard Cochran Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller